Pennock's Fiero Forum
  General Fiero Chat - Archive
  Tire Liftin, CV shaft snappin 3800 S/C

T H I S   I S   A N   A R C H I V E D   T O P I C
  

Email This Page to Someone! | Printable Version


Tire Liftin, CV shaft snappin 3800 S/C by LFiero67
Started on: 10-03-2005 01:46 AM
Replies: 11
Last post by: crash1369 on 10-03-2005 11:53 PM
LFiero67
Member
Posts: 880
From: Lethbridge, Alberta, Canada
Registered: Jun 2002


Feedback score: (2)
Leave feedback

Rate this member

Report this Post10-03-2005 01:46 AM Click Here to See the Profile for LFiero67Send a Private Message to LFiero67Direct Link to This Post
Went to Track on Friday. Looking to finally run an 11 second pass. Well I didn't quite make it to the finish, but got a pretty good video out of the trip.

I got the car good and set, convertor stalled to 2600RPM, ready to go. Come off the brakes, hit the gas and :
http://www3.telus.net/public/cornic/Fierobreak.wmv

(Please right click and save as)

You can see the front tires lift, then a spark under the car as the left CV shaft snaps, and the car comes down.

Guess I will have to wait till next year to get a time.

Mickey Thompson ET Street Drag Radials rock. That launch was at 30 psi tire pressure. They hook hard and drive nice and straight.


3800SC, powrtuned 98 PCM, TOG headers, 3" exhaust, XPcam, 2.8" pulley, ported heads, LS1 MAF, ported Throttle body, 4T60E with 3.69 gears. 235/60R15 M/T ET Street Drag Radials.

IP: Logged
PFF
System Bot
DjDraggin
Member
Posts: 2854
From: St Louis, MO. USA
Registered: Feb 2003


Feedback score: N/A
Leave feedback





Total ratings: 51
Rate this member

Report this Post10-03-2005 06:38 AM Click Here to See the Profile for DjDragginSend a Private Message to DjDragginDirect Link to This Post
NICCCEEEEEE Ohh so nice.......

------------------

Ferrari 308 GTB rebody on a modified 86SE chasis Soon to have a highly hooped up 3800SC..Ohh yeah baby!! I like a lil Whine with my meal when I go out to eat Rice
Contacts _ AIM / Zildjianfx _ Yahoo / djdraggin
Remember, always brush your milk, drink your teeth, dont do sleep and get eight hours of drugs.

IP: Logged
Will-Martin
Member
Posts: 1164
From: DFW, TX, USA
Registered: Aug 2002


Feedback score: (1)
Leave feedback





Total ratings: 63
Rate this member

Report this Post10-03-2005 07:09 AM Click Here to See the Profile for Will-MartinClick Here to visit Will-Martin's HomePageSend a Private Message to Will-MartinDirect Link to This Post
DANG that is some POWAH!

Now I am getting all goofy thinking about my swap. WOOOO HOOOO!!!

--Will

------------------
My Cardomain Website: BLACKHEART FIERO

IP: Logged
RandomTask
Member
Posts: 4540
From: Alexandria, VA
Registered: Apr 2005


Feedback score: N/A
Leave feedback





Total ratings: 150
Rate this member

Report this Post10-03-2005 08:41 AM Click Here to See the Profile for RandomTaskSend a Private Message to RandomTaskDirect Link to This Post
Ouch, sorry to hear that. Take some pictures of the damage too, I'm kind of curious to see the failure itself.
IP: Logged
lildevil
Member
Posts: 1537
From: waldorf,md
Registered: Aug 2001


Feedback score: (1)
Leave feedback





Total ratings: 56
Rate this member

Report this Post10-03-2005 06:58 PM Click Here to See the Profile for lildevilClick Here to visit lildevil's HomePageSend a Private Message to lildevilDirect Link to This Post
thats why i am afraid to use slicks! What kind of axles were you using? Are they 4t60 or 4t65e ? hope you made it home ok.

------------------
1985" TARGET=_blank>http://www.cardomain.com/memberpage/445986
1985
Fiero w/ 1998 Supercharged 3.8 V-6 Intercooled
Best ET: 12.20@ 114.90 mph (street tires)
12.00 @ 112 mph (drag radials)


"NO Juice....Just BOOST!"

IP: Logged
Rborecky
Member
Posts: 675
From: Cleveland,Ohio U.S.
Registered: Oct 2003


Feedback score: N/A
Leave feedback

User Banned

Report this Post10-03-2005 07:14 PM Click Here to See the Profile for RboreckyClick Here to visit Rborecky's HomePageSend a Private Message to RboreckyDirect Link to This Post
Nice lift. Did you stall it to take off, or just punch it?

Folks don't believe I do that but not as high and slighter slower. I have been pulled over by folks to holler that I did it. Mine has the 4t60e Heavy duty in it. Did you stall it to take of or just punch it?

------------------
President of Cleveland Fieros
www.clevelandfieros.com

IP: Logged
jsmorter1
Member
Posts: 674
From: Creston, Ohio
Registered: Jun 2004


Feedback score: N/A
Leave feedback

Rate this member

Report this Post10-03-2005 08:19 PM Click Here to See the Profile for jsmorter1Send a Private Message to jsmorter1Direct Link to This Post
real nice launch
IP: Logged
LFiero67
Member
Posts: 880
From: Lethbridge, Alberta, Canada
Registered: Jun 2002


Feedback score: (2)
Leave feedback

Rate this member

Report this Post10-03-2005 10:11 PM Click Here to See the Profile for LFiero67Send a Private Message to LFiero67Direct Link to This Post
That is on Drag Radials.

4T60E, Pontiac 6000 left and right axle is Fiero left manual CV shaft. I luckily trailered it out there, so I had a ride home.

Stalled to 2600-2700 RPM.

Picks of the carnage:


[This message has been edited by LFiero67 (edited 10-03-2005).]

IP: Logged
Jncomutt
Member
Posts: 8900
From: Charlotte, NC
Registered: Apr 2001


Feedback score: (3)
Leave feedback





Total ratings: 221
Rate this member

Report this Post10-03-2005 10:15 PM Click Here to See the Profile for JncomuttSend a Private Message to JncomuttDirect Link to This Post
Ya know it's just about right when it breaks...
IP: Logged
crash1369
Member
Posts: 326
From: Tobyhanna, PA, USA
Registered: Sep 2005


Feedback score: N/A
Leave feedback

Rate this member

Report this Post10-03-2005 10:50 PM Click Here to See the Profile for crash1369Click Here to visit crash1369's HomePageSend a Private Message to crash1369Direct Link to This Post
ive got two questions, first of all what motor do you have in your car? how much power are you making hp / tourqe. thats sux it always hurts when you break somthing like that but better you broke it at the track then driving to work or somehting stupid. my other question, which i think i know the answer to but im new so ill ask anyway. there isnt anywhere where people have the specs on thier car listed is there? maybe it should be added into their profiles that would be pretty cool just click on the profile and see what they've got. anyway good luck fixing your car, what doesnt kill it will only make it stronger
IP: Logged
LFiero67
Member
Posts: 880
From: Lethbridge, Alberta, Canada
Registered: Jun 2002


Feedback score: (2)
Leave feedback

Rate this member

Report this Post10-03-2005 10:58 PM Click Here to See the Profile for LFiero67Send a Private Message to LFiero67Direct Link to This Post
Engine specs are in first post.
IP: Logged
PFF
System Bot
crash1369
Member
Posts: 326
From: Tobyhanna, PA, USA
Registered: Sep 2005


Feedback score: N/A
Leave feedback

Rate this member

Report this Post10-03-2005 11:53 PM Click Here to See the Profile for crash1369Click Here to visit crash1369's HomePageSend a Private Message to crash1369Direct Link to This Post
oops sorry i missed that i got disstracted by the link nice air though
IP: Logged



All times are ET (US)

T H I S   I S   A N   A R C H I V E D   T O P I C
  

Contact Us | Back To Main Page

Advertizing on PFF | Fiero Parts Vendors
PFF Merchandise | Fiero Gallery
Real-Time Chat | Fiero Related Auctions on eBay



Copyright (c) 1999, C. Pennock