everything is for sale! going with the 3500, have to sell al the old stuff....
trueleo short runner intake, painted red, will strip paint before shipping if need be. its ported to the max dia of the ram-pipe (63.5mm)....$350 with 65mm tb $400
two mustang 65mm tbs, one is currently bolted to the trueleo and will only work on that manifold. $50 each
electromotive iac adaptor, comes with iac installed, allows you to use 65mm tb on almost any vehicle...$85
comp roller tipped rockers, 1.6 ratio, less than 3000 miles on them, $100
SIvalves.com's stainless steel valves, swirl polished. they measure bigger than the stock valves on the head of the valve, 1.8 and 1.6 intake and exhaust, $120
crane cams h-11 tool springs pn 99846, good for .6 inch of lift, $120 (i payed $220!)
crane cams valve spring retainers and +.050 locks.....$70
two 3.4 lower intake manifolds...$35 each (no csi port)
modified fuel rail, no csi port, $25
brand new lifters(12), sealed power, $60
crane h-272-2 camshaft, 3000 miles, great shape, USE NEW LIFTERS, $100
clevite pushrods, stock length, $35
3.4 iron head short block, zero decked, bored .020 over, 3000 miles, high volume oil pump, oil pan, timing cover, water pump, timing chain and gears, PICK UP ONLY, $400
2 distributor dummy shafts, for dis conversion, $25 each
7730 ecm from a 91 camaro with prom (has to be programed before you can use it on your fiero!!)...$80
dis coil pack with icm (3 sets of coils with icm for dis conversion) with connectors for conversion...$70
crx cold air intake, modified to fit fiero, with generic blue filter, $15
pictures on request, pay pal only, i ship when money hits my pay pal. all prices are WITHOUT SHIPPING! post up dibs along with a pm to me if your interested. thank you!
IP: Logged
11:30 PM
PFF
System Bot
AutoTech Member
Posts: 2385 From: St. Charles, Illinois Registered: Aug 2004
SIvalves.com's stainless steel valves, swirl polished. they measure bigger than the stock valves on the head of the valve, 1.8 and 1.6 intake and exhaust, $120
brand new lifters(12), sealed power, $60
Dibs, I'll contact you shortly!
[This message has been edited by AutoTech (edited 11-14-2007).]
IP: Logged
11:52 PM
merlot566jka Member
Posts: 676 From: Norman, Oklahoma Registered: Jun 2007
[QUOTE]Originally posted by merlot566jka: trueleo short runner intake, painted red, will strip paint before shipping if need be. its ported to the max dia of the ram-pipe (63.5mm)....$350 with 65mm tb $400
electromotive iac adaptor, comes with iac installed, allows you to use 65mm tb on almost any vehicle...$85
DO I NEED THE 2ND TO RUN THE INTAKE WITH THE 65 MM TB ON A 3.4 WITH CAM STOCK ECM if so i will take all of them
IP: Logged
07:45 AM
Pyrthian Member
Posts: 29569 From: Detroit, MI Registered: Jul 2002
fierobrian----yes you need the iac adaptor for the 65mm tb. i would advise that you buy both together.... and possibly the other tb. i have the thing covered in rtv, looking for a vac leak. it was never found on the upper intake....
Pyrthian, it has a vacuum port that came on it taht i used for the pcv, not in stock location. it has a fitting installed for the front of the iac adaptor (before throttle plate source). you could take out my fitting and use the iat there. i put my iat in different spots depending on the drive to change fuel out puts...lol. lmk if your still interested
88White3.4GT if he bunks you got it
patch, if he ^ bunks after the other guy bunks you got it and to all PLEASE PM ME....
IP: Logged
11:18 AM
PFF
System Bot
fierobrian Member
Posts: 2976 From: aurora il 60505 Registered: Sep 2003
grr. ur on the fiero fourms too, i want the 7730 ecm stuff. i dont need ur 87 harness cause i have an 88 but if you can get me the evap purge pigtail, egr pigtail(and however u mounted ur egr), and the ecm harness i will be very happy.,
IP: Logged
04:12 PM
merlot566jka Member
Posts: 676 From: Norman, Oklahoma Registered: Jun 2007
