Thanks all, but the car is sold. I think it will be getting an engine swap soon.

I'm trying to sell this as a lot before I decide to separate or eBay <yuck>

Red 88 Fiero GT
2.8 motor is bad, TH125 auto might be okay (but that isn't really why you are looking at this, is it? =)
Interior is dirty, needs cleaned and partially reassembled
There is rust in the trunk and surface rust underneath. I would clean this up during the swap personally, hench the delay.
Dopped the cradle out to do the swap but it back under the car for space, could be ready for you to swap.
Cradle has a spot that looks like it has been repaired. I have access to another 88 cradle.
No keys for the car.

4.9L motor and 4T60E transmission from a 1993 Cadillac DeVille with only 68,000 miles, pulled it myself and junked the car.
ECM from the 1993 Cadillac DeVille with Fiero Factory ECM chip (removes passkey, speed and rev limiters)
Fiero Factory wire harness (by Injection Technologies)
Fiero Factory mounts (for an 88 cradle)
Fiero Factory axles

With this setup and a push you should be able to do the swap pretty quick and have a V8 Fiero before the Summer ends...

Asking $3,600.00 for everything.

These were pictures I had...







------------------
-Brian

My 87 GT Poly Suspension Upgrade (all pics) thread https://www.fiero.nl/forum/Forum2/HTML/094633.html

[This message has been edited by MulletproofMonk (edited 11-05-2009).]

any chance you are willing to sell just the wiring harness? If so, I am first on the list.

These are pictures I took today... Sorry about the bad shots from the front, the car is up in the front of my garage...

Swap Parts and 4.9L





------------------
-Brian

My 87 GT Poly Suspension Upgrade (all pics) thread https://www.fiero.nl/forum/Forum2/HTML/094633.html

[This message has been edited by MulletproofMonk (edited 08-29-2009).]

Okay, lots of views but only one post. Just curious why no interest?

------------------
-Brian

My 87 GT Poly Suspension Upgrade (all pics) thread https://www.fiero.nl/forum/Forum2/HTML/094633.html

Brian:

I'll give you a bump. PM sent.

Marc

------------------
Marc in sunny Titusville, FL

• 84 SE son's car, loaded
  
• 85 Coup w/V6 transplant
  
• 85 GT newly on the road
  
• 86 SE/GT "The Chameleon" - big plans!

quote Originally posted by MulletproofMonk: Okay, lots of views but only one post. Just curious why no interest?

the rust and wear on the 88GT, mostly.

4.9L engines go for $300-400 now, and all the other parts can be had for around $500-700

if the engien was in the car, all the pumbing was done proper, and all that had to be done was wiring, i might be interested, but it is not

I might be interrested by the 2 harnesses.

Are they for stock 4.9 ECM ?

Manual or auto transmission?

PM me the price.

------------------
"I'm not driving too fast, . . . I'm just flying too low."

4.9 ongoing project

[This message has been edited by falcon_ca (edited 09-02-2009).]

Thanks for the stuff, Brian.

i want the bumpers please if your willing to part with them i could use them badly. how much and for shipment? 49509 mi

looking for a 2.8 engine cradle. Have one to sell ?

Hey Brian:

Are you parting out that 88? I'd like to get an 88 front suspenson, cradle with spindles, the whole shootin match.

Marc

------------------
Marc in sunny Titusville, FL

• 84 SE son's car, loaded
  
• 85 Coup w/V6 transplant
  
• 85 GT newly on the road
  
• 86 SE/GT "The Chameleon" - big plans!