Pennock's Fiero Forum
  The Mall - Archive
  WTB: Help me get the Final parts I need for my swap

T H I S   I S   A N   A R C H I V E D   T O P I C
  
Email This Page to Someone! | Printable Version
WTB: Help me get the Final parts I need for my swap by Mini_moosee
Started on: 09-17-2010 07:21 PM
Replies: 5
Last post by: LAMBO on 10-04-2010 05:09 PM
Mini_moosee
Member
Posts: 181
From: Edgewood, NM, USA
Registered: Jun 2010

Feedback score:    (6)
Leave feedback

Rate this member
Report this Post09-17-2010 07:21 PM Click Here to See the Profile for Mini_mooseeSend a Private Message to Mini_mooseeDirect Link to This Post
So I'm looking for a slave cylinder bracket from a 85-87 V6 4Speed
Thanks

------------------
1984 Red 4Spd "The Heartless"
1993 Chevy Lumina "Lauren"

[This message has been edited by Mini_moosee (edited 10-04-2010).]

IP: Logged
PFF
System Bot
MstangsBware
Member
Posts: 11509
From: TEXAS
Registered: Mar 2002

Feedback score:    (108)
Leave feedback





Total ratings: 459
Rate this member
Report this Post09-17-2010 08:14 PM Click Here to See the Profile for MstangsBwareSend a Private Message to MstangsBwareDirect Link to This Post
 
quote
Originally posted by Mini_moosee:

So I'm looking for an 85-87 V6 4Speed wiring harness, 85-87 V6 Engine mounting brackets, and possibly a Good condition crankshaft.

Thanks



I have the engine mount for $28 shipped...This memeber has the engine harness "hye_4_life" as I was going to buy it but found one. PM if you want the engine mount.
IP: Logged
02greens10
Member
Posts: 813
From: Ashland, Ohio
Registered: Feb 2008

Feedback score:    (24)
Leave feedback

Rate this member
Report this Post09-17-2010 08:48 PM Click Here to See the Profile for 02greens10Send a Private Message to 02greens10Direct Link to This Post
I have a harness from an 86 w/air. It's dirty and average shape. Don't remember seeing any bad wires/splices, but never ran the car. $20 plus shipping.

Is the bracket you want the front "L" bracket? I should have that and the rubber mount.

Let me make sure on the exact condition tomorrow if you are interested not going to send junk to another member.
IP: Logged
Mini_moosee
Member
Posts: 181
From: Edgewood, NM, USA
Registered: Jun 2010

Feedback score:    (6)
Leave feedback

Rate this member
Report this Post09-19-2010 06:10 PM Click Here to See the Profile for Mini_mooseeSend a Private Message to Mini_mooseeDirect Link to This Post
Bump
IP: Logged
2002z28ssconv
Member
Posts: 1436
From: Orlando, FL
Registered: Jun 2005

Feedback score:    (27)
Leave feedback





Total ratings: 50
Rate this member
Report this Post09-19-2010 11:07 PM Click Here to See the Profile for 2002z28ssconvClick Here to visit 2002z28ssconv's HomePageSend a Private Message to 2002z28ssconvDirect Link to This Post
Are you still interested in the flywheel and clutch and throwout bearing?
Personally, I wouldn't put a used clutch back in a car, but if you're just trying to get a car back on the road and the budget's tight...
This clutch was working just fine, no problems with slipping.












IP: Logged
LAMBO
Member
Posts: 1677
From: Lucas, Iowa, USA
Registered: May 2000

Feedback score: (5)
Leave feedback

Rate this member
Report this Post10-04-2010 05:09 PM Click Here to See the Profile for LAMBOSend a Private Message to LAMBODirect Link to This Post
.
IP: Logged



All times are ET (US)

T H I S   I S   A N   A R C H I V E D   T O P I C
  

Contact Us | Back To Main Page

Advertizing on PFF | Fiero Parts Vendors
PFF Merchandise | Fiero Gallery
Real-Time Chat | Fiero Related Auctions on eBay



 Copyright (c) 1999, C. Pennock