I have an SR14 Trueleo intake manifold for a 2.8l/3.1l/3.4l (Anything with a Fiero intake).

From what I read and Trueleo's claims, this is a bolt-on 10+whp for a 2.8l, would be worth more on a 3.1l or 3.4l. I had one of these on my 3.4l swap and it made a huge difference. It completely changes how the engine behaves in the upper RPM's, allowing it to pull hard to the redline instead of gasping for air above 4k.

This one is red to match the Fiero valve covers and has an EGR delete.

Trueleo sells these for 640 shipped

http://www.trueleo.com/Fierointake.htm

I'm selling this one for 350 OBO.

PIC



I also have other performance parts for V6 engines, and if you buy them as a set or paired with another part I'll give a good discount.

https://www.fiero.nl/forum/Forum4/HTML/054423.html - Ocelot stainless steel exhaust
https://www.fiero.nl/forum/Forum4/HTML/054421.html - Trueleo equal-length ceramic coated headers

[This message has been edited by MadDanceSkillz (edited 11-08-2010).]

Bump for new price

I really want that but i'm a little shy of your asking price. Free bump for you though.

quote Originally posted by DLCLK87GT: I really want that but i'm a little shy of your asking price. Free bump for you though.

Man up and make an offer.

$50 (jk)

Due to the low deck lid height on my replica, I need to know how much taller this is over the stock 2.8 manifold. Any idea?

------------------
84 2.5
87 328 GTB replica.
87 Coutach replica

quote Originally posted by Joe 1320: Due to the low deck lid height on my replica, I need to know how much taller this is over the stock 2.8 manifold. Any idea?

thats my problem, also.
it wont fix without some mod. i even loose more overhead for i have a 2' Bar above my intake for the lid support. its OEM Mera.
crap i want this soo bad and i am not so shy.......$200

Daniel-
Mera X

[This message has been edited by batousai666 (edited 11-10-2010).]

quote Originally posted by MadDanceSkillz: Man up and make an offer.

ok PM sent.....

edit to say $210

[This message has been edited by DLCLK87GT (edited 11-10-2010).]

I'm sure it could be modified for EGR...Trueleo would probably do it for a fee if you can't. The EGR delete is just the lack of a hole for the EGR tube.

You could always just mock up the EGR...lol.

As for decklid clearance, I'm not sure. The height of it really isn't any higher than the 2.8l manifold from what I can see. I've never seen anyone have to cut a hole in their decklid for one.

Dan,

I have a Trueleo intake on one of my 87 Meras so it will likely fit your vehicle.



Nelson

quote Originally posted by batousai666: thats my problem, also. it wont fix without some mod. i even loose more overhead for i have a 2' Bar above my intake for the lid support. its OEM Mera. crap i want this soo bad and i am not so shy.......$200 Daniel- Mera X

[This message has been edited by hnthomps (edited 11-11-2010).]

would you be willing to take $260?

quote Originally posted by drebinpk: would you be willing to take $260?

Not yet...

I've had one of these personally on a 3.4l...made a big difference up top.

quote Originally posted by hnthomps: Dan, I have a Trueleo intake on one of my 87 Meras so it will likely fit your vehicle. Nelson

hey thanks Nelson.....good show. i saw that pic, but i am not sure about dropping any "Mera Stuff" yet. i wanna perserve the essence that is Mera......not the engine so much, but the accessories are what make a Mera minus the panels.....you know "the little stuff"

thanks for the pic, Nelson.....good luck Dance. i still got my eye out on your stuff

Daniel

Man I want that intake so bad.

Sold