I will now be starting to build swap harnesses full time, can do either series I, II or III SC and N/A engines and also provide matching programmed PCM's and can also supply mounts and brackets when needed.
Cost or trade will also include shipping from me to you and all harnesses are custom built to your order properly made to last in your car the same way I have been building them for the last 8 plus years. Dan

------------------



http://www.photosled.com/showgallery.php/cat/631

awesome news dan..glad your back in the game!!

Yep slowly undoing all the damage my ex did to both me and my kids so I now have some time on my hands to get some work done and still enjoy some time with my family.
Kind of funny is how she did all the dirty stuff and made all the accusations of abuse but I have the kids and she gets supervised visits through childrens aid. Dan

What kind of pricing?

$400 out right or around $350 in parts value for parts I need when I am supplied with the 3800 harness to work with and $50 more when I have to supply it.
This is for the completed harness and matching PCM shipped to you. Dan

Mostly what I will be needing is suspension parts and interior parts for starters then moving on to other stuff. Dan

------------------



http://www.photosled.com/showgallery.php/cat/631

can you do a harness for a 97 3.4 TDC with a 4T65e trans? i have both harnesses and a plug and play would save me all kinds of time....i hate doing wiring

quote Originally posted by FIEROFLYER: Yep slowly undoing all the damage my ex did to both me and my kids so I now have some time on my hands to get some work done and still enjoy some time with my family. Kind of funny is how she did all the dirty stuff and made all the accusations of abuse but I have the kids and she gets supervised visits through childrens aid. Dan

Good to see you back ... and seasons greetings to you and your kids

------------------

My build Thread
http://www.tylerstoy.com
My LED marker kit

You have a PM!

Glad you are back and found some renewed purpose. I hear your harness' are top notch.

[This message has been edited by BV MotorSports (edited 12-06-2011).]

I thank you for your kind words, it has been a rough time for over a year but thankfully that is almost over with and I at least now have time to get work done and not having to focus as much on helping my kids get over all the abuse their mother put them through.
Makes you wonder how any one can hurt a child especially one of their own. Dan

Hey Dan;
I have a french speaking person out here in Quebec who is interested in your harness ... can you tell me the parameters you need to know about his setup so you can build him a harness ... THANKS I'll relay the info to him ... include all costs and shipping to Montreal.
take care
Danyel

------------------

My Build Thread
http://www.tylerstoy.com
My LED marker kits for sale

What is needed to know is the year of Fiero and if it has A/C, what year of 3800 engine is being used and what tranny so I can match the harness and PCM. Also need to know where the alternator and PCM will be mounted and if any extra things are needed for things like an air fuel ratio gauge or electric water pump and if things like the EGR and boost bypass solenoid are being retained. Dan

think you can do a 5.3L alloy truck motor harness to fit in a 2004 mazda RX8?

Just did one in the spring for a 2006 5.3l truck engine into an 87 Chevy short box so it would be about the same amount of work.
Keep in mind the 07 and newer have a different reluctor wheel so I would go with an 06 or older to make things easier with the PCM as more programming is available for the older models for this kind of stuff. Dan

Also if you go with the 5.3 truck engine with electronic TB make sure it is the three bolt one so you can easily go back to a cable TB. Dan

I have just been asked about 84 differences to the other years and think it would help to also note a few things on here.
To go from an 84 to a newer model there is many differences other then just the location of the C500, there is the speedo sensor wires that are in the C500 on the 84's and the C203 on other years as well as the two red wires below the C500 on the 85 up that feed power to the rest of the car are going through the C500 on the 84 models.
A lot of the wiring diagrams for the 84 are wrong showing cruise wiring where it is speedo wiring with the cruise wiring actually being in the other portion of the C500 that feeds the tail lights. Dan

------------------



http://www.photosled.com/showgallery.php/cat/631

Just a bump for a great product and a great guy! Very glad to see you back in the game Dan. Got a couple 3800 Projects on the horizon and will be looking for a couple harnesses. Happy Holidays!

Pat

Dan I sure wished you could do BMW V12 harness.'

Funny how the truth always comes out in the end huh?? Congrats on getting your children too.

Would need an engine to work off or a completely untouched harness to work with. Dan

Thinking of picking up a few other GM engines just for mock ups. Dan

------------------



http://www.photosled.com/showgallery.php/cat/631

I am now ahead two auto harnesses and one manual to make things faster for customers.
All harnesses come with matching computers, I cover return shipping and the usual full guarantee that I have always had for my harnesses. Dan

man, i was just kidding (kinda) about the RX8 5.3L swap, although it would be a great swap, id probably do a 03-05 5.3L for ease of install, or possible a 99-02 for no fly by wire throttle. my wife wanted the RX8, it has a bad motor, and the 5.3L 4l60E looked like a great swap for that car.

im guessing my manual trans harness already shipped if your up a harness at this point, im hoping to swap it in over the winter so i can figure out why my car is idling at 3000RPM

matthew

Yours is one of six going out Monday morning, just have one question I need answered about your harness to make sure I have the starter ignition wired to the proper pin on the C500. Dan