Good stuff, cheap!
All parts removed (or for) a couple of '86 GTs
New stuff:
************************
(1) Gauge cluster faceplate, like the brushed silver but slightly more gold.. Was that the "gold" color one? I thought they were more gold than that... Some marks here and there, best for re-painting or experimenting with? $0.00 + shipping
(1) Radio trim faceplate / vent assembly - Good shape, minor scratch - center below radio opening, brushed silver color. $0.00 + shipping
(1) Pile of cruise control parts... There's the vacuum solenoid / cable / bracket assembly from the engine side, with about 4" of wire cut off from the plug. Also the cruise computer, and wiring harness up to an 8-pin black plug and the socket for the cruise stalk wiring. Has what I believe is the clutch switch attached, a grey 2-pin plug (for brake switch?), then a cut-off yellow and grey wire coming from the same spot of the harness as the grey plug.. All for the low price of $0.00 + shipping!
************************
(1) V6 distributor - 100k miles, pickup + magnet wheel rusty, some resistance felt. Probably best as core for rebuild? $0.00 + shipping
(1) V6 aluminum alternator bracket - 100k miles, no cracks that I can see, feel, or hear by tapping on it. Typical white powdery surface, could use a good sandblasting + paint. $10 + shipping(1) 5 speed shifter assembly - 53k miles.. (Going by Odometer, but I think carfax agreed when I ran it) A little 'sticky' from someone shooting lube down there, some surface rust on lower mounting bracket but should clean up nice. Stock length. $5 + shipping(1) "Albany" brand rear pad set, probably from Autozone or Advance Auto, P/N MKD262. Box is a little beat up, but pads are new / never installed. $0.00 + shipping(1) 120MPH GT gauge cluster + faceplate (brushed silver-ish colore) 52,995 miles on odometer, good shape, no cracks. Sometimes trip odometer resets with the 1's digit between 0 and 9.. Needles are a little more orange than yellow. Has about 6" of wiring harness on the 2 main connectors. $20+ shipping(2) GT center gauge pods. Both have the add-in wiring harness. Both dark grey / black color, one some cracking on top left corner of vinyl, clear plastic has no cracking, 1 bottom side mounting post is cracked off, no silver-ish bezel. Best used for gauges only maybe? Needles are a little more orange than yellow. $0.00 + shipping
2nd center gauge pod has slight warping along top front edge and bottom left corner. Tiny crack on left top rear corner, some scuffs / shiny wear on right side + corner.. Clear plastic has some cracking on lower edge visible in bezel opening. Has silver-ish bezel in good shape except either some black stuff or chipped off paint between the 2 gauges. Also has lower metal bracket, but it's really rusted. Needles are pretty much yellow. $0.00+ shipping ("Buy" both and swap parts around?)
-- Just found another dark-colored center gauge housing, this one has no cracks or much wear, but has some warping on the top and left. This one also has the lower metal bracket, in good shape with some surface rust. All of the above parts for $0.00 + shipping if you want them all together.. Ooh! Just found a perfect non-cracked clear plastic piece too...
(1) Set of grey horn paddles for non-GT steering wheel. Pretty good shape, slight chip in grey on right side paddle, lower right corner just beside the face.. $5 + shipping. Whoops, just saw the clips broke off the left side paddle.. They're supposed to hold the paddle from swinging forward. Still perfectly usable I think.. But now $0.00 + shipping Just found another left-side only horn paddle. No cracks! About 2" of wire attached. Solder the pair together and you have 1 good set. Newly found paddle included, still $0.00 + shipping.(28) Black plastic screw-on lug nut caps. They all look to be in good condition. $0.00 + shipping
(1) V6 upper intake assembly - red non-engraved plenum, throttle body / sensors, EGR tube. All would need re-finishing - red is peeling off, bare aluminum (TB) is pretty oxidized.. EGR doesn't feel cracked, but still has (worn) OEM heatsheilding so I can't inspect without cutting it off.. Whole assembly - $0.00 + shipping(1) V6 middle intake manifold. (the one that the red manifold bolts to) Gasket bits still stuck to it, you can see scotchbrite marks from the last time it had gaskets replaced but it looks to be in good shape. 100k miles. $0.00 + shipping(2) Jones Exhaust tube mufflers, P/N A4512S. I have 2 of these on my 3800SC now, others have them as well, fairly loud IMO.. 4" body, 12" long, 2.5" pipe. Plain steel, mine rusted pretty quick, I'd suggest painting them. These are new, never installed. $25 each from Summit or Full Line Exhaust.. $15 for the pair + shipping
(1) Pair V6 exhaust manifolds. No cracks (that I can see), flanges are quite rusty though. 1 bolt broken off in each one. $0.00 + shipping
(1) Delco EQ tape player / radio. All black face and knobs, I'm not sure if this was OEM Fiero or if someone installed it from another GM? Dolby Noise Reduction, yahoo!!
Good shape except for minor scratch at top right of display... Er.. Now that I look at it closely... What I thought was "gunk" (looks like someone sneezed on it) I now realize is what can only be described as clearcoat peeling in spots.. The matte texture is gone, leaving shiny spots. $0.00 + shipping. Good if you really need a vintage radio and can't afford a perfect one I guess!
I also have a single 3800 exhaust flange, from ZZP or one of the other 3800 places.. .31" thick steel, no EGR hole. Also a pile of exhaust manifold tubing from Summit - looks to be mostly 1 3/8", a straight piece and mandrel U / J-bends. $0.00 + shipping for all of it.. Might be a couple $ shipping, it is steel after all..
That's it for now! I'm sure there's more around somewhere.. I'm going to give it a week or two, what's left is going in a dumpster. I've been holding on to it for too long, and have no reason (or room) for it any more..
I can get pics of any of it, just let me know if you need them. I would take and post them all now, but I just don't have the time. It's been a rough weekend and there's way too much to do still. Just had to get this all out there before I toss it all in case anyone wants any of it.
It's all in MA also, in case anyone wants to pick anything up..
PM or email - riceburner98 (at) gmail (dot) com
Thanks for looking!!!
------------------
Bob Williams
(still) working on the 3800 swap... It'll drive some day!
[This message has been edited by Riceburner98 (edited 05-04-2012).]
