Where to jack rear (Page 1/2)
Xenoblast MAR 19, 11:33 AM
I am pulling the transmission to replace the throwout bearing, but to pull it out I need to drop 3/4 of the cradle mounts. I usually jack my car in the rear by the cradle, but obviously cant do that. I know theres that image with the jack locations, but it is way too vague. The red points on the image there is literally not enough space to put a jackstand there.

https://images.fiero.nl/2015/JackPoints2_1.gif

Can someone post an image showing how they jacked their car? All I see on the internet is people using a long 4x4 across the entire car, but I am not doing that.

[This message has been edited by Xenoblast (edited 03-19-2022).]

skywurz MAR 19, 01:01 PM
Well.. id say still jack it from the cradle but support with the stands not on the cradle. You should never get under a car thats not securely on stands.

Edit.
I use the 4x4 method when dropping the cradle ever since i dropped a couple Fieros off of stands doing cradle work. You don't jack the 4x4 you use it with stands to supplement support. Prior to that i would support with stands in about the same place but if the car shifts those stands will fall and drop the car.

[This message has been edited by skywurz (edited 03-19-2022).]

Xenoblast MAR 19, 01:14 PM

quote
Originally posted by skywurz:

Well.. id say still jack it from the cradle but support with the stands not on the cradle. You should never get under a car thats not securely on stands.

Edit.
I use the 4x4 method when dropping the cradle ever since i dropped a couple Fieros off of stands doing cradle work. You don't jack the 4x4 you use it with stands to supplement support. Prior to that i would support with stands in about the same place but if the car shifts those stands will fall and drop the car.




I apologize, I meant where do I put the jackstands to support the car to work on it. I am using a hydraulic jack on the cradle to lift up the car to start with.

On the red points, my jackstands cant support it in the middle without colliding with the coolant tube, and I was wondering if there is another point near it that I could put them

[This message has been edited by Xenoblast (edited 03-19-2022).]

IMSA GT MAR 19, 01:32 PM
I'm not sure if you made a mistake with the colors. The green is how you are jacking up the car right now by the cradle. The PINK is the jackstand locations and there are many of them. They are labeled "safety stands".


But to use the factory jack locations (in red), most people do this:

[This message has been edited by IMSA GT (edited 03-19-2022).]

Xenoblast MAR 19, 01:47 PM
Oh Yeah I misunderstood the labels, on most cars the pinch weld is where you could put a jackstand so I assumed the same with this car. Also, is this a suitable jack stand location? It looks like this is one of the pink spots on the diagram.



This is the front left subframe mounting spot if you couldnt tell, there is a curved lip on one side which looks like a stand point. on the other side there is a coolant line in the way but its rubber so I should be able to push it out of the way.

[This message has been edited by Xenoblast (edited 03-19-2022).]

cvxjet MAR 19, 02:08 PM
I lifted my Fiero and mounted it on jackstands positioned on the frame rails just forward of the cradle forward-mounts...Then supported the engine (With Fiero store engine support) and dropped the subframe, and then dropped the trans (But not on my head (Slowly learning from past mis-takes)

I removed the rear wheels and set them (Basically) in the frunk for better balance.

Here is a quick pic of where the jackstands go ;
olejoedad MAR 19, 04:35 PM

quote
Originally posted by cvxjet:

I lifted my Fiero and mounted it on jackstands positioned on the frame rails just forward of the cradle forward-mounts...Then supported the engine (With Fiero store engine support) and dropped the subframe, and then dropped the trans (But not on my head (Slowly learning from past mis-takes)

I removed the rear wheels and set them (Basically) in the frunk for better balance.

Here is a quick pic of where the jackstands go ;




We have used the jackstands in those spots for years with no issues.
theogre MAR 19, 05:05 PM
See my Cave, Jacking to Clear Engine

------------------
Dr. Ian Malcolm: Yeah, but your scientists were so preoccupied with whether or not they could, they didn't stop to think if they should.
(Jurassic Park)

The Ogre's Fiero Cave

skywurz MAR 19, 07:37 PM

quote
Originally posted by cvxjet:

I lifted my Fiero and mounted it on jackstands positioned on the frame rails just forward of the cradle forward-mounts...Then supported the engine (With Fiero store engine support) and dropped the subframe, and then dropped the trans (But not on my head (Slowly learning from past mis-takes)

I removed the rear wheels and set them (Basically) in the frunk for better balance.

Here is a quick pic of where the jackstands go ;



Yeah I've used that spot too i like to use a 4x4 across as I've had slipping issues.
cvxjet MAR 19, 08:37 PM
One thing I always do now when using jackstands; After they are in place and I have lowered the car onto them, I lower the jack approx' 1/8" below the frame and then I stand to the side and jerk on the car to make sure it is solidly supported. Once, when I did this, the car slid forward slightly- I had not repositioned the wheel chocks after jacking (At the top of the jack arm-swing the car can be moved backward- moving it AWAY from the forward chocks- Just kick them backwards tight against the tires BEFORE Lowering)

Always use chocks front AND back on the GROUNDED tires when jacking.