 
     |
| Using a Pressure / Power Bleeder for the Clutch Master - Finding an Adapter That Fits (Page 1/2) |
|
xetura
|
OCT 29, 04:28 PM
|
|
Hey all. I'm looking for a pressure/power bleeder adapter for the clutch master cylinder. I attempted to make one out of an old cap, but the cap is too flexible and leaks all over the place. If there's another vehicle that uses the same cap that's stronger, I could use that to make my own. But I'd prefer one I can just order and not have to worry about it. I tried a couple off Amazon, but they don't fit. Pics of the ones that DON'T fit are attached. Thanks.
****As much as I appreciate it, I'm not interested in people posting all the different bleeding methods. I know how to do it. This is about finding a pressure bleeder cap for the Clutch.****
|
|
|
Patrick
|
OCT 29, 04:45 PM
|
|
| quote | Originally posted by xetura:
I attempted to make one out of an old cap, but the cap is too flexible and leaks all over the place.
|
|
Years ago I did just that... and it didn't leak. Just letting you know that it is possible to successfully do.
|
|
|
|
xetura
|
OCT 29, 04:52 PM
|
|
| quote | Originally posted by Patrick:
Years ago I did just that... and it didn't leak. Just letting you know that it is possible to successfully do. |
|
I've seen pics of older caps and they look much sturdier than the one I have (which is newer). I'm not sure which one you used, but the newer ones are flimsy and thin.
|
|
|
|
Patrick
|
OCT 29, 04:57 PM
|
|
I wasn't aware that there was a difference between "older" and "newer" clutch master reservoir caps. The one I used was probably an original cap from the 80's.
You did say you used an "old cap".[This message has been edited by Patrick (edited 10-29-2024).]
|
|
|
|
Larryinkc
|
OCT 29, 05:20 PM
|
|
|
|
|
fieroguru
|
OCT 29, 06:01 PM
|
|
I have used these in the past. Just need to keep the gaskets in place and regulate the air pressure to single digits.
Any more, I just bleed the manual way with a hose in a bottle.
|
|
|
|
Patrick
|
OCT 29, 06:20 PM
|
|
| quote | Originally posted by fieroguru:
...and regulate the air pressure to single digits.
|
|
That's probably the secret to success. Back when I was still using this method to bleed the system, I just used a hand vacuum/pressure pump.[This message has been edited by Patrick (edited 10-29-2024).]
|
|
|
|
Vintage-Nut
|
OCT 29, 09:26 PM
|
|
|
To me, purging air from a hydraulic system is so easier with vacuum than pressure or the gravity method....... ------------------
Original Owner of a Silver '88 GT
Under 'Production Refurbishment' @ 136k Miles
|
|
|
|
larafan
|
OCT 30, 09:13 AM
|
|
|
I recently bought new master and slave from Rodney Dickman along with his bleeder kits and was very simple 1 man operation per his instructions. Bench bled the master and installed. Swapped the slave and elevated the rear and used his 1-waay bleeder. Easy.
|
|
|
|
Dennis LaGrua
|
NOV 02, 12:08 PM
|
|
| quote | Originally posted by Vintage-Nut:
To me, purging air from a hydraulic system is so easier with vacuum than pressure or the gravity method.......
|
|
We've bled the clutch slave cylinders with a vacuum bleeder and have achieved good results. ------------------
" THE BLACK PARALYZER" -87GT 3800SC Series III engine, custom ZZP /Frozen Boost Intercooler setup, 3.4" Pulley, Northstar TB, LS1 MAF, 3" Spintech/Hedman Exhaust, P-log Manifold, Autolite 104's, MSD wires, Custom CAI, 4T65eHD w. custom axles, Champion Radiator, S10 Brake Booster, HP Tuners VCM Suite.
"THE COLUSSUS"
87GT - ALL OUT 3.4L Turbocharged engine, Garrett Hybrid Turbo, MSD ign., modified TH125H
" ON THE LOOSE WITHOUT THE JUICE "
|
|
|
