Greengoblin's Build Thread! (Page 4/12)
greengoblin0129 JUN 03, 01:06 AM
ERRR
My tail light/ guage cluster fuse kept blowing any time I turned on my lights. So I tried a 25amp fuse and they started working. I walked to the back of the car to see if the tail lights were still on. They were, but very dim. So I opened my door to a TON of smoking coming out from under the dash I quicky turned off the lights, switch no longer worked, so I pulled the fuse (very hot). So I started tearing apart my guage clusted to get to the wiring harness....sure enough...the rubber coating around the copper had melted off on the whole orange wire coming out of the switch going to the fuse box, WTF? Got pi$$ed and ended up going out for the night, in the other Fiero (alway have to have a back up when you own a Fiero ) I'll find out whats goin on tomorrow with it and get some pics.

[This message has been edited by greengoblin0129 (edited 06-03-2006).]

greengoblin0129 JUN 04, 02:07 AM
Got the light issue solved...I ran all new wires and took out the 2 bad ones
greengoblin0129 JUN 04, 09:19 PM
The air ride project is coming along! Should be done in time for the Auburn show, heres some teaser pics:
Cut the top piece to test fit the cups:

Test fit of cup on bottom:

My buddy had a couple of extra cups that I could test fit to see which ones would be best:


***I'm not using this steering rack for the air ride project (to rusty). I use this one to test on before I cut into my good one (sry, you don't get to see pics of that yet, its a secret ) Theres still a lot of notching to be done but should be done pretty soon! By using the S10 cups i'll be able to get a lot more lift, trust me
greengoblin0129 JUN 06, 12:23 AM
Did some work on the front bumper today. I ended up putting the front lip on a different nose because the one I previousy had it on had the 85GT trim on it... So here's how it looks now:
Bumper off the car:

Front lip on bumper:
(custom spray paint lol)
Inside of bumper:

another view of it:


I got 2 different sets of fog lights today and neither fitted how I wanted them to, so i'll try to find some tomorrow that I like. More pics to come
tuner2m6t JUN 06, 12:38 AM
Looking good hope to see it at Auburn.
greengoblin0129 JUN 06, 10:38 PM
Spend most of my day working on my front bumper and working on my buddies Camaro. I finally found some foglights I like, and they fit perfect (after taking 2 sets back lol). Also had a guy come over to help me out with the air ride project, its getting close now. I won't post pics of that till after its done Heres the pics of the front bumper, wired up the fog lights and fixed some body work on it.
Fog light kit:

Hid all the wiring, can't see any of it under the hood ar inside the car:
before:
after:
Bumper:

Bumper w/ lights on:

[This message has been edited by greengoblin0129 (edited 06-06-2006).]

Joe Torma JUN 07, 12:37 AM
Looks good. Good luck with your air ride! You're going for as high as you can get it looks like?

[This message has been edited by Joe Torma (edited 06-07-2006).]

YELLOWFIERO88 JUN 07, 12:43 AM
^^^ With those nasty Indy roads you need it to go high
greengoblin0129 JUN 07, 01:07 AM

quote
Originally posted by Joe Torma:

Looks good. Good luck with your air ride! You're going for as high as you can get it looks like?




I'll be able to lay out fine, but I'm also trying to get a lot of lift out of it as well. I'm going to have to run the newer slam bags because they don't sweal up when you inflate them, therefor I don't have to worry about the bags rubbing as much. Was just going to run sleave bags, but I want to mess around with it and don't want to chanch breaking somthing. I might not be using the S10 anymore either...i'll be working on it all day tomorrow hopefully.

Ryan
greengoblin0129 JUN 07, 01:10 AM

quote
Originally posted by YELLOWFIERO88:

^^^ With those nasty Indy roads you need it to go high



They probley just seemed nasty to you becasue your ebreak was stuck on the whole time you were coming into Indiana lol j/k