 
     |
| 4.9 Parts where to BUY (Page 1/17) |
|
Capt Fiero
|
MAY 04, 05:45 PM
|
|
|
Here is my list of where and what I need. ECM Chip Arriving on Tuesday or Wednesday. Special chip for Dual O2 Sensor Elderado motor. 3/4 done FieroHut (John) about the wiring of the Fiero to Caddy Got It -- I am buying a motor from a 93 Elderado with ECM and Harness for $700 CDN, about 570 American Auto Wreckers in Tuckwilla Washington Got It -- I am buying a separate Isuzu Trans to replace my shot 4spd Muncie. $100 CDN Got it -- Getting Flywheel from LSC Performance in California made from Billet steel for 215$ USD Shipped. BEST PRICE AROUND. Got it
Exhaust shop will do the Y-Pipe as I plan to use the stock Exhaust. $260 CDN Got It -- Oil Cooler from Performance Radiator $40 CDN Please suggest any shops you can think of or places to locate stuff. Part Numbers of things that I need at the shops would be great.
------------------
85GT 4spd MSD Everything, Big Cam and Nitrous. www.captfiero.com
  
[This message has been edited by Capt Fiero (edited 12-11-2005).]
|
|
|
|
Pink_Ninja
|
MAY 04, 06:05 PM
|
|
|
err sorry to kinda hijack but... ...what are you gonna do with the blown 4 spd? wanna part with it?
|
|
|
|
GT
|
MAY 04, 06:08 PM
|
|
|
Greg Duncan from the Cadero List sells the flywheels. There used to be a link on Ed Parks' page to contact him. Also Ed Parks may have one or two for sale. There was also a thread on Pennock's a few months ago by a guy who was having a flywheel manufacturer make him one. It was going to be $350US but I can't find the link to that thread and I don't know how that turned out. You might do a web search on flywheel manufacturers. -Rick [This message has been edited by GT (edited 05-04-2005).]
|
|
|
|
Capt Fiero
|
MAY 04, 06:10 PM
|
|
|
4spd is being repaired, and used as back up for my (yes believe it or not) my mother's 86 SE V6 4spd. She has a bad 3/4 synchro and I don't know how much longer it will last. My 4spd just needs a bearing kit and new input shaft bearing and new clutch fork release bearing.
|
|
|
|
Capt Fiero
|
MAY 04, 06:11 PM
|
|
| quote | | Originally posted by GT: Greg Duncan from the Cadero List sells the flywheels. There used to be a link on Ed Parks' page to contact him. Also Ed Parks may have one or two for sale. There was also a thread on Pennock's a few months ago by a guy who was having a flywheel manufacturer make him one. It was going to be $350US but I can't find the link to that thread and I don't know how that turned out. You might do a web search on flywheel manufacturers. -Rick |
|
P.S. GT-Rick gets a plus, Thank you, Thank You, Thank You. Ok runs off to send email to caddero forum and email Ed Parks. [This message has been edited by Capt Fiero (edited 05-04-2005).]
|
|
|
|
DanFiero
|
MAY 04, 10:45 PM
|
|
|
Capt. Email sent about parts needed for the swap. Dan
|
|
|
|
Capt Fiero
|
MAY 04, 10:55 PM
|
|
|
That spreadsheet is AWESOME. Thank You. I have added a 2nd coulomb for what my estimated prices are. I am at over $3100 cdn so far. I wish we had a car quest in Canada however I guess Lordco and the Dealer will have to be my next best bet. ------------------
85GT 4spd MSD Everything, Big Cam and Nitrous. www.captfiero.com
|
|
|
|
Capt Fiero
|
MAY 05, 12:35 PM
|
|
|
Ok so it has now been close to 24hrs since I emailed out to BubbaJoe about mounts and posted on the cadero forum about buying a flywheel and no one has responded yet. ??? That seems to be strange. Anyone got a direct email addy for greg duncan.
|
|
|
|
Mickey_Moose
|
MAY 05, 01:31 PM
|
|
|
Check around some local driveline machine shops about getting the fly wheel done, you should not have a porblem finding one that will do it for you. On a side note, I seem to recall a post that Master Tuner Akimoto made that he will do up flywheels as well. Bubba mounts - I would suggest that you have him ship the front mount without the holes drilled on the bottom plate (the block hole are ok) as you may have to relocate them. I have seen 2 cars that needed to hole relocated. I could not get the rear mount to line up correctly using the holes that he drilled in the front mount. Not sure what you are planning on with the dog bone, but if you are not going to use the original mount on the trunk side I would suggest that you remove it as it gives a bit more room for when you need to change plugs. If you don't mind can you forward the parts list to me? Just curious as I never really made one up for when I did my swap.  Tim
|
|
|
|
86fieroEarl
|
MAY 05, 02:33 PM
|
|
| quote | | Originally posted by Capt Fiero: Ok so it has now been close to 24hrs since I emailed out to BubbaJoe about mounts and posted on the cadero forum about buying a flywheel and no one has responded yet. ??? That seems to be strange. Anyone got a direct email addy for greg duncan. |
|
I make sets of mounts also, Both comes with no holes drilled so you don't have relocation problems.... There pretty easy to make if you got a welder.... If you still don't get ahold of bubba give me a pm I make sets also but I would need atleast 3days leed time to make them and takes 3days to get to you.
ppl use me for mounts if they need cheap mounts made up for them. And need them quick (well 6days)
only thing is mine requires you retain the black mounting bracket on the engine block to use.
about the flywheel send MTA a pm I believe he still makes them for the 4.9, My setup is using his flywheel and itfit nicely and works great.
Purchase a $40 dollar flywheel brandnew from a 3.1 cavilier and have him machine it...
And I thought there was only once source to get a wire harness from? never knew about FieroHut (John) doing wire harnesses, Im going to need one done in hte future.
------------------
 [This message has been edited by 86fieroEarl (edited 05-05-2005).]
|
|
|
