Pennock's Fiero Forum
  General Fiero Chat - Archive
  what tools for bumper removal- HELP!

T H I S   I S   A N   A R C H I V E D   T O P I C
  
Email This Page to Someone! | Printable Version
what tools for bumper removal- HELP! by fibercustoms
Started on: 01-01-2004 04:23 AM
Replies: 4
Last post by: Fierobruiser on 01-03-2004 01:38 AM
fibercustoms
Member
Posts: 43
From: san diego, ca
Registered: Nov 2003

Feedback score: N/A
Leave feedback

Rate this member
Report this Post01-01-2004 04:23 AM Click Here to See the Profile for fibercustomsClick Here to visit fibercustoms's HomePageSend a Private Message to fibercustomsDirect Link to This Post
i found a 2M4 at the junkyard. front and rear bumpers. can someone tell me exactly what tools i will need to remove them both? also, side skirts.
thanks
Joel
IP: Logged
PFF
System Bot
spddy
Member
Posts: 815
From: Concord ,ca usa
Registered: Mar 2003

Feedback score: N/A
Leave feedback

Rate this member
Report this Post01-01-2004 04:35 AM Click Here to See the Profile for spddyClick Here to visit spddy's HomePageSend a Private Message to spddyDirect Link to This Post
7mm socket, ratchet, phillips screwdriver,and a fork tool for removing
clips and in about 10 min you should be able to get it off
good luck
IP: Logged
James Bond 007
Member
Posts: 8872
From: California.U.S.A.
Registered: Dec 2002

Feedback score: (1)
Leave feedback





Total ratings: 263
Rate this member
Report this Post01-01-2004 11:34 AM Click Here to See the Profile for James Bond 007Send a Private Message to James Bond 007Direct Link to This Post
I think you'll need a hammer and chisel to pop the rivets on the rear bumper cover.
IP: Logged
SLagrec1
Member
Posts: 241
From: Troy, Michigan
Registered: Aug 2003

Feedback score: N/A
Leave feedback

Rate this member
Report this Post01-02-2004 08:08 PM Click Here to See the Profile for SLagrec1Send a Private Message to SLagrec1Direct Link to This Post
We used a Trim Removal Set to detach the urethane (?) bumper from the honeycomb. Local places like NAPA have them but here's a pic from Eastwood:

http://www.eastwoodco.com/itemdy00.asp?T1=52021&Dep_Key1=

Good luck!

------------------
Steve, 87 Fiero GT, Getrag w/Ultimate Shift Kit, Street Dreams drop spindles, Poly mounts, KYBs, Ocelot, DashScan

IP: Logged
Fierobruiser
Member
Posts: 1951
From: Gilbertsville,PA USA
Registered: Aug 2001

Feedback score: N/A
Leave feedback





Total ratings: 57
Rate this member
Report this Post01-03-2004 01:38 AM Click Here to See the Profile for FierobruiserSend a Private Message to FierobruiserDirect Link to This Post
They work well and I recommend the door panel tool #52035 on the right there also.

------------------
Notchbacks RULE

"It's cool to have a car you just have to look back at."

IP: Logged



All times are ET (US)

T H I S   I S   A N   A R C H I V E D   T O P I C
  

Contact Us | Back To Main Page

Advertizing on PFF | Fiero Parts Vendors
PFF Merchandise | Fiero Gallery
Real-Time Chat | Fiero Related Auctions on eBay



 Copyright (c) 1999, C. Pennock