Ok, As alot of you ppl may have noticed, I have huge goals for my fiero, fastback swap in process, I'll be making a new nose, and MODing up some Rocker / front fender / QP combo thing... I'll explain more on those maybe later...
But heres something I've been thinking about...
A 4th brake light, or... removing the 3rd and doing this...
A brake light on an 87 fastback where the light runs the length of the spoiler, or a brake light that is on the rear of the spoiler...
Anyone understand ?
Could someone PS it on a fastback with the stock taillights, and also with the 355 replica taillights please ?
~Tim
IP: Logged
04:30 PM
PFF
System Bot
FieroMaster88 Member
Posts: 7680 From: Mattawan, MI Registered: Nov 2000
I have 5" stands on my 88GT.I added an LED light strip wired into my stop lights and used a Lawrence settup to make that light blink rapidly for a few seconds before it stays on.I mounted it to the groove on the underside of the spoiler and ran the wires through one of the stands and the trunk lid.
------------------ #1112 Question my ability,question my intelligence,never question my integrity!
IP: Logged
06:25 PM
Master Tuner Akimoto Member
Posts: 2267 From: South Florida,USA Registered: Jul 2003
i also looking for a led strip about 40" to replace my 3rd brake light. i wanted to go across the back window. i got an cadillac STS 3rd brake light that's mounted in the trunk but it's too long and it has a little arc.
i did find an 31" led strip but it also had an arc.
where can i find a straight/flat led strip light?
thanks, toms...
------------------
IP: Logged
10:39 PM
James Bond 007 Member
Posts: 8871 From: California.U.S.A. Registered: Dec 2002
Be aware that the large light bars run $100 to $150 or more.JC Whitney sells a nice 14in light bar.I baught a 3 foot light bar from a company on the internet and it wasnt even in a houseing (there web sight shows it encased in plastic)I have a 14 in. led bar up high and am ready to put another one under the spoiler.The added 3rd or 4th brake light can reduce rear end colisions significantly.Also do an internet search for a product called BackOFF it's a flasing or pulsed device that attaches to the third or fourth brake light for increased visibility.
[This message has been edited by James Bond 007 (edited 07-25-2004).]
IP: Logged
10:39 PM
twentyeight Member
Posts: 946 From: Grand Rapids, MI Registered: Aug 2003
In Michigan, when adding a spoiler with a third brake light, you must disable one or the other, afaik. I don't know if that applies everywhere, but be advised.
I'll be removing the factory 3rd brake light if i do the LED idea... Mainly b/c i plan on doing something w/ my rear window...
But yea, I'd like to put one on the spoiler almost the full length of it... it would take some fiberglassing and such, b/c id liket o keep the car aerodynamic (nothing hanging off the spoiler) and stream line...
Dan Bunker from N.C. already has one in his spoiler from a Cadillac STS. It was molded-in. Looks good , but sorry , I have no pics of it. He doesn't frequent the Forum.
Any LED that would fit... and where i could get 1... Anybody know ?
I'm not even sure what will fit... Could someone help me research it ? This is why I posted about it... To see if it has been done, if its possible, and to see if you guys could help me out on getting the How-To info....
Right now, Im curious what will fit, and where I'd get it...
If anyone has pix of this already done... Or any brake light MODs, please post them....
IP: Logged
12:42 AM
Silicoan86 Member
Posts: 1614 From: Savage, MN, USA Registered: May 2004
Made my own from a 3rd brake lite in a eclipes spoiler! Then molded it in to the underside of the roof ( there is about 1" lip) no one sees it till I hit the brakes ( with hidden brake light switch on ) wire it directly in to the stock brake light wires !
Disregard the reflection on the scoop in the middle ( dam shiny clear coat ) and YES I SEE THE LIGHT OUT
------------------
98 3800SC GTP motor,3.4 pulley, Getrag 5sp. custom hood, trunk, side scoops, IRM front spoiler, 17" excel's , dk.Shadow Grey
[This message has been edited by revin (edited 07-26-2004).]
IP: Logged
10:27 PM
Tom Slick Member
Posts: 4342 From: Alvarado, TX Registered: May 2003
I personaly think the Honda Accord brake light on some of their spoilers would work better than the Cadillac STS light. It is long , but it is also straight. The Caddy light has a slight arch in it. Look on Ebay , there's usually quite a few on there.
IP: Logged
03:21 AM
Master Tuner Akimoto Member
Posts: 2267 From: South Florida,USA Registered: Jul 2003
I bought one last week(cadillac 32 leds) and cut off the screws and left the outside ones got 2 small L brackets covered the back in grey cloth material and turned it upside down and it fits inside like a glove and covers the whole back window.
[This message has been edited by Master Tuner Akimoto (edited 07-27-2004).]
IP: Logged
07:54 AM
Tom Slick Member
Posts: 4342 From: Alvarado, TX Registered: May 2003
Originally posted by Ronnie: I personaly think the Honda Accord brake light on some of their spoilers would work better than the Cadillac STS light. It is long , but it is also straight. The Caddy light has a slight arch in it. Look on Ebay , there's usually quite a few on there.
seeing the Honda one in the spoiler, that's what got me start in thinking about doing it in the spoiler first.
after my 3rd brake light housing broke and seening the cadillac STS light, i thought that would be cool to have it go across the back window.
quote
Originally posted by Master Tuner Akimoto:
I bought one last week(cadillac 32 leds) and cut off the screws and left the outside ones got 2 small L brackets covered the back in grey cloth material and turned it upside down and it fits inside like a glove and covers the whole back window.
MTA, got any pics? which cadillac one do you have?
that looks great. i want one to go across the whole back window. any idea?
thanks, thomas...
Why YES here is one............
They make a long brake/ turn signal light for p/u trucks that fits in between the tailgate and bumper ( look in JCWhitney) It plugs into the trailer conn. and is the length of the tailgate. I am thinking that it will fill the back of the window. It is like $99 A little snip and cut here and there and ta da
------------------
98 3800SC GTP motor,3.4 pulley, Getrag 5sp. custom hood, trunk, side scoops, IRM front spoiler, 17" excel's , dk.Shadow Grey
IP: Logged
09:24 AM
PFF
System Bot
Master Tuner Akimoto Member
Posts: 2267 From: South Florida,USA Registered: Jul 2003
They make a long brake/ turn signal light for p/u trucks that fits in between the tailgate and bumper ( look in JCWhitney) It plugs into the trailer conn. and is the length of the tailgate. I am thinking that it will fill the back of the window. It is like $99 A little snip and cut here and there and ta da
Yep that is the one ! A little bit of modding it can be done. can you solder? Glue? that is about what would need be done. remove a few led's, maybe glue the end cap back on . I had to cut the houseing on the elclipes lites in half to fit under the roof. super glued the back half on and never had a prob with water getting in there!
I do love those caddy lights they seem curved though?
Made my own from a 3rd brake lite in a eclipes spoiler! Then molded it in to the underside of the roof ( there is about 1" lip) no one sees it till I hit the brakes ( with hidden brake light switch on )
I didn't know you had that! it's way cool. Is that new for the fall 2004 season??
IP: Logged
02:09 PM
Aug 13th, 2004
Tom Slick Member
Posts: 4342 From: Alvarado, TX Registered: May 2003