I have a great set of sail panels that just need a spray job with a rattle can, $20 plus shipping. I have a set of 5-speed Getrag cables "somewhere", I need to dig them out to be sure. I'll let you know.
can i get a pic of the sail panels? they are basically sold and are getrag and isuzu shift/selector cables inter changeable? idk i have isuzu 5 spd how much for the cables and shipping on sails to 48506
[This message has been edited by DEMONCHILD (edited 10-30-2007).]
IP: Logged
12:56 AM
KurtAKX Member
Posts: 4008 From: West Bloomfield, MI Registered: Feb 2002
Originally posted by DEMONCHILD: can i get a pic of the sail panels? they are basically sold and are getrag and isuzu shift/selector cables inter changeable? idk i have isuzu 5 spd how much for the cables and shipping on sails to 48506
I do not knwo if Isuzu and Getrag cables are interchangable and knowing GM I would bet they are not. Yes, I have a picture of the sail panels. I'll post it here later when I get the time with shipping.
IP: Logged
10:04 AM
Toddster Member
Posts: 20871 From: Roswell, Georgia Registered: May 2001
What SD4 stuff have you got? I didn't see anything on ebay....
The SD stuff will take a white to dig out. I am working through one pile at a time. But in brief I have one complete 2.7 engine (windowed, needs rebuilding), One SD 2.5 shortblock (brand new and built by Huffaker), one Cosworth 4V head, one SD head, One header, Various pistons, valves, ignition systems, intakes, carbs, etc. I gots lots!
IP: Logged
10:07 AM
KurtAKX Member
Posts: 4008 From: West Bloomfield, MI Registered: Feb 2002
Can you call me? Or e-mail at kevin.sullivan@horacemann.com? I want to be sure our calandars are in synch. In other words, I do not want to drive into town when you might be out doing other things. 916.600.6482
Thanks for the anticipatory expedient reply.
Sincerely, Kevin J. Sullivan
IP: Logged
01:22 PM
Toddster Member
Posts: 20871 From: Roswell, Georgia Registered: May 2001
Can you call me? Or e-mail at kevin.sullivan@horacemann.com? I want to be sure our calandars are in synch. In other words, I do not want to drive into town when you might be out doing other things. 916.600.6482
Thanks for the anticipatory expedient reply.
Sincerely, Kevin J. Sullivan
I'll be around ALL weekend just pulling parts and putting up ebay auctions!
IP: Logged
01:35 PM
Toddster Member
Posts: 20871 From: Roswell, Georgia Registered: May 2001
Originally posted by DEMONCHILD: can i get a pic of the sail panels? they are basically sold and are getrag and isuzu shift/selector cables inter changeable? idk i have isuzu 5 spd how much for the cables and shipping on sails to 48506
IP: Logged
11:30 AM
Formula88 Member
Posts: 53788 From: Raleigh NC Registered: Jan 2001
I really hope that whoever buys the EHPS keeps it off his/her car. That thing is historic, man! I can't believe you're selling it!
------------------ 1984 Fiero SE, White, first love, sold... 1986 Fiero SE 2M6, gold 1988 Fiero 2M4, the Fox 1987 Fiero GT, Blue, 3.4/4T40 Still looking for that perfect CJB 88 GT...
IP: Logged
01:15 AM
pokeyfiero Member
Posts: 16203 From: Free America! Registered: Dec 2003
I really hope that whoever buys the EHPS keeps it off his/her car. That thing is historic, man! I can't believe you're selling it!
I peresonally want it to make exact duplicates. The control board would cost a couple grand to have a set up made but after that they would only cost about 5 bucks each to reproduce in lots of 100. The pump and rack on the other hand I have no idea. I do believe people would pay at least 500 bucks for a stock power steering system.
IP: Logged
02:01 AM
Formula88 Member
Posts: 53788 From: Raleigh NC Registered: Jan 2001
Originally posted by pokeyfiero: I peresonally want it to make exact duplicates. The control board would cost a couple grand to have a set up made but after that they would only cost about 5 bucks each to reproduce in lots of 100. The pump and rack on the other hand I have no idea. I do believe people would pay at least 500 bucks for a stock power steering system.
It's not hard to swap in an F-body or Corvette steering rack. The pump is the issue on most cars. Replicate the electric pump and controller, and the biggest hurdle of the swap is covered. Otherwise, you're usually stuck going with an engine with a stock power steering pump and running lines from the back of the car.
IP: Logged
07:52 AM
RUNDLC Member
Posts: 802 From: Elk Grove, California Registered: Jul 2005
Just on the caliper itself. You have enough to do 1 caliper or 2? I need both brakets:
One "set up", in other words, I am not removing nuts and bolts. I'll be happy to sell you two calipers complete. They aren't of much use to anyone without the springs and arms. $15 each plus shipping.
IP: Logged
02:13 PM
PFF
System Bot
kevin Member
Posts: 2722 From: Elk Grove, CA USA Registered: Jan 2000
Dear Todd, I coming in from Elk Grove tomarrow. Arrival time around around 11:00a.m. concerning the tranny(s) we spoke of earlier. Can you call my cell 916-600-6482 to let me know when you get this e-mail? I lost your adress in Morgan Hill as well as your cell number. Sorry :- (
Thanks
Kevin J. Sullivan
IP: Logged
03:53 PM
Toddster Member
Posts: 20871 From: Roswell, Georgia Registered: May 2001
Dear Todd, I coming in from Elk Grove tomarrow. Arrival time around around 11:00a.m. concerning the tranny(s) we spoke of earlier. Can you call my cell 916-600-6482 to let me know when you get this e-mail? I lost your adress in Morgan Hill as well as your cell number. Sorry :- (
Thanks
Kevin J. Sullivan
**** happens. Details sent.
IP: Logged
04:52 PM
FierOmar Member
Posts: 1644 From: Glendale, California, USA Registered: Dec 2001
One "set up", in other words, I am not removing nuts and bolts. I'll be happy to sell you two calipers complete. They aren't of much use to anyone without the springs and arms. $15 each plus shipping.
You know, I didn't think of that. No wonder I couldn't get anyone to send me some . These are going on cores as for some reason they are not on my old set. I'm afraid I don't need more calipers but than you very much. I think there is a junk yard near me I might try and get some from. I might check back with you on some other things that I need though.
Josh
IP: Logged
10:17 PM
Nov 4th, 2007
Toddster Member
Posts: 20871 From: Roswell, Georgia Registered: May 2001
Small request. Please don't email me asking if I will close an auction for less than the starting bid price. I won't. If you want it, bid. If not, don't.