You don't wanna play games bud........I am a true ahole and am proud of it......just remember that. And thanks a million two the two people who I have sent p.m.'s to for the helpful advice on actually resolving my issue. I do appreciate help from fellow Fiero people!!!!!!!!!!!!!!!!!!!!!!! Brian Welcome for the defence neils88.......I have read many of your posts and do know how SMART you are.......we all make mistakes.....we are only human!!!
You don't wanna play games bud........I am a true ahole and am proud of it......just remember that. And thanks a million two the two people who I have sent p.m.'s to for the helpful advice on actually resolving my issue. I do appreciate help from fellow Fiero people!!!!!!!!!!!!!!!!!!!!!!! Brian Welcome for the defence neils88.......I have read many of your posts and do know how SMART you are.......we all make mistakes.....we are only human!!!
Gawd...just what we need....another big bad internet guy...
Nope I'm not......just to get on your nerves.........have I yet?????.....oh wait I haven't tried....lol......anyway like several of my posts have states very clearly. These forums are here for good info.....which was given in the first few posts in this thread. It was started about SPACERS..., not adapters......which by the way are not DOT APPROVED...........so if anyone has any input about what this thread was started about........ Great!!!! If its about adapters.....then fine start a thread about them....and go to that thread.......THANK YOU......AND HAVE A GREAT DAY...... THANKS FOR THE P.M. ON THE SPACERS FIEROMASTER........THE TECH DEPT WAS VERY HELPFULL AND FOUND WHAT I NEED.....THANKS AGAIN!!!!!!!!!!!!! Brian
Whoop dy doo.......I mean really......this stupid forum is full of a bunch of pussies. Stay on topic and read what a thread is really about. Some real ignorant idiots here thats for sure Piss off to all.............. Thanks again to PATRICK AND TOP NOTCH. YOU HAVE BOTH BEEN VERY HELPFUL IN RESOLVING A ISSUE SOMEONE WAS TRYING TO RESOLVE.......THANKS A BUNCH........DO APPRECIATE THE INFO Brian P.S. TO THE REST OF YA..YOU KNOW WHO I AM TALKI G ABOUT. PISS OFF YOU BUNCH OG BABIES If ya want my address....just ask....I will settle the issue face to face......see if you can walk the walk. Little man........
[This message has been edited by bkw88 (edited 09-01-2015).]
Whoop dy doo.......I mean really......this stupid forum is full of a bunch of pussies. Stay on topic and read what a thread is really about. Some real ignorant idiots here thats for sure Piss off to all.............. Thanks again to PATRICK AND TOP NOTCH. YOU HAVE BOTH BEEN VERY HELPFUL IN RESOLVING A ISSUE SOMEONE WAS TRYING TO RESOLVE.......THANKS A BUNCH........DO APPRECIATE THE INFO Brian P.S. TO THE REST OF YA..YOU KNOW WHO I AM TALKI G ABOUT. PISS OFF YOU BUNCH OG BABIES If ya want my address....just ask....I will settle the issue face to face......see if you can walk the walk. Little man........
Ummm....ok Homer. Stay away from the roids. You're a funny guy.
This is the Fiero wheel fitment diagram. What you can do here is use the measurements to see the offset of the stock wheels and compare to the new wheels you would like to buy. You'll have to do some math because the 88 had front 6" with 37mm offset and rear 7" by 30mm offset. Compare to your new wheels with "X" inch width and offset.
Spacers are fine. Someone else can do the math to see the thickness you need. Like I guessed its prob around a 1/4" I had a set laying around that were 1/4" id give you for free to try, but dont know where I put them. If you need thicker, you might want to replace the studs with longer ones to be safe. You could experiment around with a bag of flat washers to see what works, then just measure how thick your stack is. Put 4-5 flat washers on each stud for a starting point and add or subtract from that. You can bolt on the wheels over the washers, just dont drive on it.
Spacers are fine. Someone else can do the math to see the thickness you need. Like I guessed its prob around a 1/4" I had a set laying around that were 1/4" id give you for free to try, but dont know where I put them. If you need thicker, you might want to replace the studs with longer ones to be safe. You could experiment around with a bag of flat washers to see what works, then just measure how thick your stack is. Put 4-5 flat washers on each stud for a starting point and add or subtract from that. You can bolt on the wheels over the washers, just dont drive on it.
Finally some one with a reasonable answer instead of adding to a big pizzing contest. Thank you.
Finally some one with a reasonable answer instead of adding to a big pizzing contest. Thank you.
Yep....
Roger I went ahead and bought some 5mm spacers and when I get them I will go from there ... ...If it doesn't look right I am gonna do the washers ideal until satisfied.
If I have to go beyond 5mm then I will replace the studs with longer ones as you have suggested. Thanks..
[This message has been edited by fireboss (edited 09-02-2015).]
Let's have a time out!
...If it doesn't look right I am gonna do the washers ideal until satisfied.
