I hope you're keeping a set or two in stock - someone from the Fiero group on Facebook was inquiring about these so I referred them to this thread. Maybe I'll actually have a reason to pick one up eventually, too.
I saw that, I told the guy to send me a message and id give him your number. Also when I get back I have another core to send ya.... Just take care of me on my IMSA swap and pau the shipping and its yours
[This message has been edited by pontiackid86 (edited 08-28-2013).]
Finally got around to working on my junk and thought I would post pictures of Jasons modded rails mountes. Hands down the best looking fuel rails for the 3800. I have a second set that will be going on another swap in the future.
In reply to all PM's , I am gearing and getting supplies together and make a few. Please confirm your commitment so that I can get an accurate count of how many I need to make. Thanks for your interest. -Jason
Update for the people that are interested and ordered. I have the lines bent up and waiting to get the rail cores. I have to make a trip to the salvage yard this weekend to pick up a few. Thanks for your patience. -Jason
*
Also, no depost or payment is needed until the rails are ready to ship. At that time, I will email you to let you know your set is done and ready to go.
[This message has been edited by Fierofreak00 (edited 01-20-2014).]
update: Still working on them and I got a couple almost done but I ran out of acetylene. It will be Delivered tomorrow and I'll get them finished up. -Jason
Middle of the process workup A couple need the return line and map bracket installed. Plus the legs need to be modified to fit intercoolers.
As a side note, all cores can be cut to save on shipping on your end. I only need the regulator and the lower rails.
You can cut them with a hacksaw just be sure to not nick or cut the lower rails. You should be left with the lower rails with the FP regulator attached, you can discard the extra tubes as they are not needed. -JC Cut at the lines shown on the green tape.
[This message has been edited by Fierofreak00 (edited 05-12-2014).]
I have no cores at the moment anybody that needs rails will have to be patient until I can get a few sets....Thanks for your continued support and patience. -Jason
Also I would like to ask anyone that has purchased from me in the past, (or in the future) to please post pics and some feedback for me. Thanks!
[This message has been edited by Fierofreak00 (edited 06-11-2014).]
Luke, Spiders1, JCircs your rails are almost done.
FieroTrev2014, Fierofan25 I have come up with extra cores so two additional sets will be available.
I believe I have accounted for all that have PM'd me and sent cores, If I missed anyone, let me know asap. I'm going to the GM Carlisle National's this weekend and need to get everything in order before I leave to ship when I return.
PM's will be incoming shortly with payment and shipping info. Luke, I will send you additional info where we can meet up this weekend.
I'm sending them as I'm making them, yours will be one of the next two out. I spoke too soon last week before Carlisle...I will keep you updated -Jason
Spiders1, Fierofan25 PM's sent for payment instructions.
JCircs I received your payment, and the box is on the shipping shelf at this moment. All I'm waiting for is the invoice from our shipping dept for your tracking number.
FieroTrev2014 PM sent for payment instructions , I did have an extra one that you inquired about. If your not interested anymore, please let me know.
Thanks to all. -Jason
Now that I have caught up on building them. I have one extra set in the box ready to ship, If anyone's still needing one. -Jason
Received my rails today already painted and installed, they look awesome. FYI if you plan on using the WCF low alternator setup you will need to modify the tensioner pulley bracket. You should be able to see in the pictures how much needed to be removed.
.JPG)
.JPG)
.JPG)
_1.JPG)
.JPG)
.JPG)
