Pennock's Fiero Forum
  The Mall
  WTB oil pressure sensor feed line from block to sensor

Post New Topic  Post A Reply
Email This Page to Someone! | Printable Version


 next newest topic | next oldest topic
WTB oil pressure sensor feed line from block to sensor by oneinch
Started on: 03-08-2021 07:23 PM
Replies: 5 (633 views)
Last post by: MulletproofMonk on 03-11-2021 12:44 PM
oneinch
Member
Posts: 119
From: PA
Registered: Oct 2020

Feedback score: N/A
Leave feedback

Rate this member
Report this Post03-08-2021 07:23 PM Click Here to See the Profile for oneinchSend a Private Message to oneinchEdit/Delete MessageReply w/QuoteDirect Link to This Post
Edit: I no longer need this. Thanks all.

I want to buy the oil feed line from the block to the pressure sensor. My line is corroded at the block. If I remove - and I want to remove it - the line is going to twist and break. I wish to replace it with a non corroded line.



------------------
Stanton
'88 Formula, red on gray

[This message has been edited by oneinch (edited 03-11-2021).]

IP: Logged
PFF
System Bot
blackrams
Member
Posts: 32487
From: Covington, TN, USA
Registered: Feb 2003

Feedback score:    (9)
Leave feedback





Total ratings: 229
Rate this member
Report this Post03-08-2021 09:55 PM Click Here to See the Profile for blackramsSend a Private Message to blackramsEdit/Delete MessageReply w/QuoteDirect Link to This Post
My advice is to either manufacture one yourself or contact Jeremy at Fiero Factory, my bet is, he has one hanging on the wall.

Rams
IP: Logged
skywurz
Member
Posts: 1031
From: CA Usa
Registered: Feb 2006

Feedback score: (2)
Leave feedback

Rate this member
Report this Post03-08-2021 11:29 PM Click Here to See the Profile for skywurzClick Here to visit skywurz's HomePageSend a Private Message to skywurzEdit/Delete MessageReply w/QuoteDirect Link to This Post
I have one
IP: Logged
blackrams
Member
Posts: 32487
From: Covington, TN, USA
Registered: Feb 2003

Feedback score:    (9)
Leave feedback





Total ratings: 229
Rate this member
Report this Post03-09-2021 07:16 AM Click Here to See the Profile for blackramsSend a Private Message to blackramsEdit/Delete MessageReply w/QuoteDirect Link to This Post
 
quote
Originally posted by skywurz:

I have one


Well, there ya go.
IP: Logged
wannav8
Member
Posts: 150
From: tx
Registered: May 2019

Feedback score: (3)
Leave feedback

Rate this member
Report this Post03-09-2021 10:48 AM Click Here to See the Profile for wannav8Send a Private Message to wannav8Edit/Delete MessageReply w/QuoteDirect Link to This Post
I have a couple also if it does not work out with above.
IP: Logged
MulletproofMonk
Member
Posts: 3088
From: Dayton, OH (Bellbrook, OH 45305)
Registered: Oct 2005

Feedback score:    (50)
Leave feedback





Total ratings: 78
Rate this member
Report this Post03-11-2021 12:44 PM Click Here to See the Profile for MulletproofMonkClick Here to visit MulletproofMonk's HomePageSend a Private Message to MulletproofMonkEdit/Delete MessageReply w/QuoteDirect Link to This Post
I tried this, but my fitting at the other end wasn't a 1/4npt. https://www.fiero.nl/forum/Forum2/HTML/140843.html

------------------
-Brian

My 87 GT Poly Suspension Upgrade (all pics) thread
Removing the roof panel
My HUD install thread
Modified stock air canister and base to 3.5 inch for 3800na

IP: Logged

next newest topic | next oldest topic

All times are ET (US)

Post New Topic  Post A Reply
Hop to:

Contact Us | Back To Main Page

Advertizing on PFF | Fiero Parts Vendors
PFF Merchandise | Fiero Gallery
Real-Time Chat | Fiero Related Auctions on eBay



 Copyright (c) 1999, C. Pennock